Forum pracy nad projektem wskrzeszenia The Forge Forum Index Forum pracy nad projektem wskrzeszenia The Forge

 
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   GalleriesGalleries   RegisterRegister 
 ProfileProfile   Log in to check your private messagesLog in to check your private messages   Log inLog in 

mbt schuhe Also gave me a partial feed antenna plu

 
Post new topic   Reply to topic    Forum pracy nad projektem wskrzeszenia The Forge Forum Index -> Forum
View previous topic :: View next topic  
Author Message
defgf60hv
Cholerny Spammer



Joined: 03 Nov 2010
Posts: 886
Read: 0 topics

Location: England

PostPosted: Fri 8:38, 10 Dec 2010    Post subject: mbt schuhe Also gave me a partial feed antenna plu

Also gave me a partial feed antenna plug \

Bl1800C head feed tray. Feed with a hacksaw to cut a disk from the edge of the opening,[link widoczny dla zalogowanych], (Editor's Note: This approach will increase the damage to feed the signal attenuation, undesirable), stuck in the side of the feed rod feed antenna (Figure i), the first KU head aligned with the satellite, will connect one end of a hard-wire the center of the antenna connected to the KU head the other end of the center of mouth, the hard-wire fixed with hot (hot melt adhesive can be a little crowded.) KU head removed, mounted on the feed tray with the first C (C head with mouth and feed Handicap Qi) to find the focus of the center of the C head aligned hard-wire port at one end and let the head center and the hard-C wire with a straight line C in this position fine-tuning the position and tilt head,[link widoczny dla zalogowanych], the strongest signal is the best focus of the position. Then think of ways to melt with iron tablets and fixed-line edge of the C headers, and adjust the metal mesh to make the strongest signal so far. Method two: use the appropriate length of aluminum, the aluminum bending (bending slightly d, on the edge of the pot from the antenna, the farther part of the greater curvature d,), fixed to the pot with hot rim; or to aluminum one end section bent into u-type, the card and then melt in the pot rim fixed. First with a small amount of double-sided tape to stick a little aluminum foil tape aluminum strip has been fixed. Aluminum bending to adjust to the strongest signal so far,[link widoczny dla zalogowanych], and then aluminum foil tape double-sided adhesive tape won the paste more fixed, the best melt the aluminum foil and then a little bit better packaging tape fixed to the aluminum bar, or a long time will fall off (Figure D), (Figure V). Some of what I made with this modified C head fixture and installed 0.75 ordinary antenna feed tray, flip reception is much weaker than the dress. Without. Pre wings are fitted to the next 166. E satellite 3860H28000 a signal that 6.3dB, flip to find a day after the signal 3860H28000 this group, just flash a display 4dB never appeared on the signals. Finally, dress back, the signal soon found 6.3dB, this result is repeated twice. I do not feed efficiency, and if so, I will test the equipment being installed on the feed efficiency with the flip closed 166. E satellite results. The wings of wind capacity is limited, generally live in the top of the wind but also to the typhoon would have obediently removed the antenna before, the fear is that the summer storm ... .... Friends of a star drill on the edge of the pot holes in the screw installation, and removal than with hot firm is also convenient. Network Rail,[link widoczny dla zalogowanych], iron, hacksaw, scissors bar, hot melt glue gun (well used, the family should be standing) are sold in hardware stores, can not find. Aluminum foil tape (my film is used in the packaging industry, relatively thick and large) to buy a few packs of large packaged potato chips, shrimp crackers, which the bags can be used. Installation. Reception after the wings: a 3dB SNR increase of about 1, the receiver 166. E satellite, all-Chinese, the other stations only 3977V3253, 3987V3253 (foreign language) could not make. After 6 plus wings 3740H27500 8.83829H13240 SNR SNR SNR 5.8 plus 4.5 plus 8.23836V22000 after wings wings wings added later, after 7.83860H28000 9.64080V30000 SNR SNR 6.3 without the addition of wings, the wings after the 7.84060H26470 signal to noise ratio of 5.9 after adding noise ratio without the addition of wings after 8.53940H27690 6.92, the receiver 138. E satellite, plus. Pre wings could not make, plus all post-noise ratio under the 3460V30000 6.93664H3617 7.33660V30000 SNR SNR SNR 113867H4290 7.93,[link widoczny dla zalogowanych], receive 1od. 5. E satellite, plus. Pre wings could not make, plus all post-noise ratio under the 3660V27500 7.83960H27500 8.63796V2626 SNR SNR SNR 8.64020V27500 8.54000V27500 signal to noise ratio SNR 8.44148V11852 7.74, the receiver 105. 5. E satellite, plus. Fujian, Taiwan, under the wings of the former only, plus \Asia 6.63729H136501, / B84.63806V4420 5.3-53-Guangxi
More articles related to topics:


moncler doudoune Eicon Networks Diva Server media

[link widoczny dla zalogowanych]

tory burch outlet Purchase of computer accessories


The post has been approved 0 times
Back to top
View user's profile
Display posts from previous:   
Post new topic   Reply to topic    Forum pracy nad projektem wskrzeszenia The Forge Forum Index -> Forum All times are GMT + 2 Hours
Page 1 of 1

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum

fora.pl - załóż własne forum dyskusyjne za darmo
Powered by phpBB © 2001, 2005 phpBB Group
Regulamin