Forum pracy nad projektem wskrzeszenia The Forge Forum Index Forum pracy nad projektem wskrzeszenia The Forge

 
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   GalleriesGalleries   RegisterRegister 
 ProfileProfile   Log in to check your private messagesLog in to check your private messages   Log inLog in 

# # # Cube

 
Post new topic   Reply to topic    Forum pracy nad projektem wskrzeszenia The Forge Forum Index -> Forum
View previous topic :: View next topic  
Author Message
fasfsdas
Cholerny Spammer



Joined: 25 Sep 2010
Posts: 5145
Read: 0 topics

Location: England

PostPosted: Thu 2:44, 25 Nov 2010    Post subject: # # # Cube

3. Then let the middle edge pieces into place.
the white face turned to the next, find the red and green side of the block, if the red and green on the top side of the block according top clockwise until the edge of the block in Figure 1 on the same situation,[link widoczny dla zalogowanych], in accordance with the formulas rotating cube, so that side of the block into place. If the red and green side of the block in the middle of a layer, but in the wrong place or color error, the first block on the right side of the red and green position in front, and then re-spin in accordance with one of the following sequence 1.


4. Then the top (should be yellow) side of the block to adjust upward, making yellow cross. If the rotation in accordance with formulas 1, the top not a yellow cross, repeatable formulas by turning, until the yellow cross appears.

*** tips and share with you:
First of all, *** cube, we must first understand its structure, 6-color 6-sided cube, each side is divided into the central block (the middle of the block 6),[link widoczny dla zalogowanych], corners (4 corner block Cool and the side blocks (four at the edge of the block 12). Of which only one side the central block, they are a fixed structure, so central is the red block, then the red should be the other side to this focus. And red is always the center of the block opposite the central block of orange (international standard is so specified). The block has two side faces two colors, corners there are three faces three colors.
5. Then adjusted to cross the yellow around corners, a bit difficult to see formulas clue.

6. Usually this time yellow block, and the dislocation will have the color of the side, according to formulas (I have not fully digested) to locate the four corners of the yellow block.

then there will be letters to describe a layer or a rotating surface, and direction: for example: R (on behalf of the right 90 degrees clockwise), R `(on behalf of the right turn 90 degrees counterclockwise), R2 (2 times on behalf of the right turn 90 degrees clockwise)
following is shown:


Next we will use the letters on behalf of each sides,[link widoczny dla zalogowanych],

final note is: the name of each side is relative, for example, F is the front of the cube is the time for his own hand side, if we imitate the rotation to the other side, then there is a new side of a front.

Well, let's try the next
the following 7 steps to restore the cube it!

1. first side of the middle of the block is white (with a piece of rubiks logo) facing the top, and then make a white cross at the top, that is, all other colors of the blocks to the appropriate position (small complex, see picture,[link widoczny dla zalogowanych], note the subject of the above formulas Oh, did correct )

7. Finally, the edge of the color and then adjust to the corresponding location. You're done!! Thrill.
2. Then the white corners homing (Cheats said, very complex and easier to understand, or plug-Rights)

*** Sina


The post has been approved 0 times
Back to top
View user's profile
Display posts from previous:   
Post new topic   Reply to topic    Forum pracy nad projektem wskrzeszenia The Forge Forum Index -> Forum All times are GMT + 2 Hours
Page 1 of 1

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum

fora.pl - załóż własne forum dyskusyjne za darmo
Powered by phpBB © 2001, 2005 phpBB Group
Regulamin